Blog

How Do Garbage Disposals Work?

This month we’ve been talking a bit about garbage disposals and how to keep them clean but how do they even work? It is a fair question! For most folks it’s just enough to know they do work, but knowing how they work can help you address problems early, and how to get the most out of your garbage disposal. So. This time on the Economy Plumbing Services Blog we’re answering just how garbage disposals work!

How Do Garbage Disposals Work?

The garbage disposal is made up of a few parts that work together to grind up food waste into a slurry that’s safe to run through a drain pipe. Here are the various parts and how they work.

The Hopper Chamber

This is the hollow cylinder that sits beneath your sink and houses the disposal proper. There are two portions – the upper and lower chambers. Food enters through the drain into the upper hopper chamber before it’s shredded up.

The lower hopper is insulated, and holds the motor to the disposal. It also connects to the waste line. After the food is ground up it moves through one the top to the lower chamber on it’s way out of the drain pipe. The lower hopper will also have a reset button on the bottom.

The Flywheel and the Shredded Ring

The shredder ring sits between the upper and lower chambers, right smack dab in the center of the disposal. The shredder ring has inner walls made up of sharp grooves that help grind up and break down food. If you think of it like a cheese grater you’re halfway there! The flywheel is a rotating metal turntable that’s attached to the bottom of the shredder ring. It prevents any food from entering the lower hopper chamber until it’s small enough to safely go through the sides of the shredder ring and down the drain. The flywheel connects to the next pieces in the disposal unit, the motor and impellers.

The Motor and Impellers

It shouldn’t come as any surprise that garbage disposals have motors. After all, when you flick the switch and hear it rev up there’s got to be something powering those grinding features right? A typical motor generates between a half and ¾ horsepower of force. The motor rotates the flywheel and the impelleers that are attached it, rotating them up to two thousand times per minute (or 2000 RPM). When you think of a garbage disposal you probably think it has some sort of blade in there right? That’s why you don’t want your hands in it right? Those ‘blades’ are the impellers. They fling food chunks into the shredder ring which breaks up the chunk so food. This happens back and forther until the food chunks are small enough to go past the shredder ring and down the waste line.

The Waste Line Connector

The waste line connector, housed in the lower hopper chamber is the final section of the disposal. From here the shredded, ground-up food particles fall and are washed out with the water, leading into the drain pipe.

The Power Cord

Because your garbage disposal needs electricity to power its motor, there is a power cord attached to it. This plugs in a normal outlet that is in the wall under your sink. 

What Breaks When It Breaks

PROBLEM: IT WON’T START

Chances are this is an electricity problem, not a problem with the disposal proper. Take a look at the reset button. Press it and try turning your disposal on again. Sometimes a simple reset is all that’s needed. If that still doesn’t fix it take a look at the plug and the outlet. 

When it comes to electricity, you usually don’t want to do any of these jobs yourself as it’s more dangerous than other at-home DIY jobs. 

PROBLEM: IT’S JAMMED

If the disposal is jammed it’s probable that the impellers are stuck. Unplug the disposal from the wall to prevent any accidents and then look for a hole at the bottom of the lower hopper chamber. It should be hex-shaped. Take a hex wrench that fits it and put it into the hole then work the wrench back and forth to free the impellers.

PROBLEM: IT LEAKS

With all the connecting parts and pieces in your garbage disposal there are many places a leak can happen. Figure out where the leak is coming from, then try and tight any loose pieces. There’s a chance that a gasket has worn down in the connections and water is leaking past it. If the water is dripping from the button of your lower hopper chamber, like where the reset button is, bad news. That disposal is toast. The gasket that keeps water where it should has been worn down and water has run through the electronic components of your disposal.

Time to call a professional for a new disposal unit.

PROBLEM: IT WON’T GRIND

Make sure you’re running water while you use the disposal and that you’re only putting foodwaste down the drain that the disposal can handle. If those two things are true and the disposal still isn’t breaking down the food then it’s likely the impellers and/or shredder ring have dulled. If this is the case then the option is to either replace those components individually or take a look at replacing the whole disposal. 

Having trouble with your garbage disposal? Need help troubleshooting problems or just need a new unit entirely? You know what to do.

If water runs through it or to it, we do it!

Recommended Posts

water pipe emergency repair

How to Respond Quickly When a Major Pipe Burst Occurs

A major pipe burst can flood your Tucson, AZ home in minutes. Stay calm, act fast, and call an emergency plumber once you've stopped the flow. How to Deal With a Major Pipe Burst, Fast Protect Your Family If you've got small children or pets nearby, get them out of the affected area right away. Either the water itself or an electrical issue could endanger them, and they won't know how to stay out of your way or keep themselves safe. Shut Off the Water Head straight to your home's main shutoff valve: don't worry about assessing the damage or grabbing any belongings yet. Turn the valve clockwise until it stops. In most homes this valve is in the basement near the water heater, by the front foundation wall, or where the main line enters from the street. Turn Off the Electricity If the burst is near any outlets, lights, or appliances, turn off power to those areas at your breaker box. Only do this if you can reach the panel safely without stepping in deep water. If it feels risky, leave it alone and wait for help. Drain Remaining Water from the Pipes With the main water supply off, open all the cold-water faucets in the house and flush the toilets once. This relieves pressure and empties the lines so there's less water to keep spraying from the burst spot. Leave the faucets open until the flow slows to a drip. Document Everything Before Cleanup Get photos and videos of the damage right after you've stopped the water. You'll want evidence of the burst pipe, your wet floors, any affected walls and furniture, and damage to any belongings. You will need this for your insurance claim later, and the insurance companies will need proof that the damage came from this burst pipe rather than something else. Move Belongings and Contain the Water Lift rugs and move electronics, furniture, and important papers out of the wet zone. If the water is spreading, roll up towels or use plastic sheeting to block doorways and keep it from reaching other rooms. Work fast but safely. Don't carry heavy, soaked items if they're too heavy for you, and focus on irreplaceable items first, like photos, electronics, and documents. Call a Tucson, AZ Emergency Plumber Don't wait if water is involved, because every minute you lose is another minute for mold to grow or a new problem to develop.  A good emergency plumber can isolate the problem, make a temporary repair if it's after hours, and plan for a permanent fix as soon as possible while coordinating with a restoration team. Start Removing Standing Water While you wait for the plumber, use mops, towels, a wet/dry vacuum, or buckets to get water off the floor. The faster you remove it, the less it soaks into subfloors or walls. Open the windows and run fans to improve airflow if the weather allows. Your aim is getting the area as dry as possible. You've got this. Act fast, and call us at Economy Plumbing Service, LLC at 520-885-3510 for the best emergency plumbing service in Tucson.

Tankless or Traditional: What’s the Best Water Heater Option for Your Home?

The decision between tankless and traditional models for replacement water heaters in Tucson can make a real difference in your daily comfort and long-term costs. Let's take a closer look at how each type works, which will help you pick the right fit for your household. Traditional Heaters Traditional tank-style water heaters store a set amount of water, usually 40 to 80 gallons, in an insulated tank and keep it hot constantly using either gas or electricity. When you turn on the faucet, hot water flows from the tank while cold water refills it at the bottom. Tankless Heaters These heaters only give you hot water when you need it. Cold water passes through a heat exchanger inside the compact unit, and out comes hot water, nearly instantly. Pros of Both Let's consider the pros of the traditional heaters first: They're cheaper up front Installation is simpler because most homes already have the connections in place When it needs replacing, it's simple and often same-day They can handle a high flow rate (lots of usage simultaneously) The pros list for the tankless heater is also enticing: Less wasted energy from water being heated when it's not needed No running out of water, no matter how many people take showers Longer tank lifespan Takes up less space Cons of Both Here's the downsides to be aware of with traditional heaters: They use more energy (much more, in some cases) They run out of hot water, and you have to wait while they refill They're bulky and need more room for placement They need to be replaced sooner than tankless As for tankless heaters, be aware that: Installation costs are usually higher Initial purchase price is higher Flow rate is lower unless you invest in a bigger (or multiple) units Scale can form inside the heat exchanger faster than in a tank model Best Water Heaters in Tucson: Local Factors There are a few local factors that might also influence your decision. We have hard water, so that means scaling is more of an issue. Both types of heaters need to be flushed to prevent buildup, but the tankless might need it more often. We've also already got high energy bills with the hot summers we have here, so trimming that with a tankless model can make a big difference over time. Tankless water heaters pay for themselves in energy savings in about seven years, and if you take care of your model, it can last up to 20.If you're still weighing the options for your specific setup, give us a call at Economy Plumbing Service LLC here in Tucson at 520-885-3510. We're a family-owned business with more than seventeen years of honest, no-pressure service here in Tucson. We'll walk through your usage, space, and water conditions to help you choose the heater that actually fits your home and lifestyle. We also serve clients in Vail, Rita Ranch, Oro Valley, Green Valley, and surrounding areas.

Gas line repair and inspection in Pima County, AZ.

Are Your Gas Lines in Safe? Warning Signs You Can’t Ignore

We rely on our gas lines in Tucson to heat our homes, give us instant hot water, power our stoves, and more. Keeping your gas line safe is a serious responsibility, because the dangers of a problem in the gas line can be deadly. Here's some warning signs to look out for. Warning Signs That Gas Lines in Tucson Are in Trouble Emergency Signs Some warning signs are emergencies, and you cannot ignore them. Call your gas provider or emergency services and leave the area immediately if: You smell a sulfurous odor in or immediately around your house People in the house are suddenly and inexplicably experiencing headaches, dizziness, nausea, or shortness of breath If gas is escaping into the house, it can cause you and your family serious physical harm. The gas, as you breathe it, begins to displace the oxygen in your blood. You gradually asphyxiate or suffocate if you are exposed to too much for too long. Non-Emergency There are other warning signs that are less immediately serious, but you need to pay attention to them, regardless, as they could quickly turn serious: Corrosion Always inspect your pipes regularly, and if you see rust or other corrosion on them, be sure to call a qualified contractor right away. There may also be an issue if you notice flaking or bubbling of paint near your gas lines or a lot of dampness and residue around the fittings. A professional can seal joints and even replace a bad section of pipe if needed. Hissing If you hear hissing near a gas appliance or a meter, it likely means that gas is escaping. Even a little bit of a leak can increase your bills, of course, and indoors, it can create a very dangerous condition. Contact a professional contractor right away to take a look. If it's a single appliance, turn off the gas to that appliance. Bigger Bills If your habits haven't really changed, but the cost of your gas bill keeps going up, try turning off all your gas appliances and writing down the meter reading. Then, wait for an hour or two and check the meter again. If it has gone up, you have a leak. Low Pressure If the flame on your stove or in your furnace doesn't have the power it should have, then you could have a leak somewhere in the line leading to that appliance, or there could be a blockage. There also could be a faulty regulator in the appliance itself or corrosion in the piping. If several appliances seem to be affected, then the issue could be farther down the line and could be either your responsibility or something that your utility company needs to deal with. A contractor can investigate the situation and help you figure out what's going on. If you're noticing any issues with your gas line, schedule an appointment with us at Economy Plumbing Service LLC in Tucson or call us 24/7 at 520-885-3510. We also serve Vail, Rita Ranch, Oro Valley, and Green Valley.